Roper M6707-1-1 Instrukcja Użytkownika

SUPER PRO GUN &SUPER PRO GUN IIMaintenance & Repair ManualMAGNUM VENUS PRODUCTSSUPER PRO GUN &SUPER PRO GUN IIPart No. M6707-1-1Revision 0

SUPER PRO GUN &SUPER PRO GUN II3. Screw the 5105-10-1 (Trigger Nut) into the 5110-7-1 (Gun Handle)and tighten. Coat the 5110-4-1 (trigger stem) w

SUPER PRO GUN &SUPER PRO GUN II9. Set the 5105-6-1 (Toggle Washer) into the washer seal seat of the5110-1-1 (Porting Plate) large side down.10. Se

SUPER PRO GUN &SUPER PRO GUN II7SUPER PRO GUNGun Block Assembly 5104-00-01Chapter31. Install the 7301-11-008 (O-Ring) onto the 5104-25-1(Flush Val

SUPER PRO GUN &SUPER PRO GUN II81. Check for and remove debris and burrs in 5104-1-1 (Gun Block).2. Install the two 5104-3-1 (Secondary Seals) in

SUPER PRO GUN &SUPER PRO GUN II7. Press firmly, or tap with a hammer until the seal assembly bottomsout in the 5104-1-1 (Gun Block), then gently r

SUPER PRO GUN &SUPER PRO GUN II14. Press firmly, or tap with a hammer until the seal assembly bottomsout in the 5104-1-1 (Gun Block), then gently

SUPER PRO GUN &SUPER PRO GUN IIFig. 3.618. Install the 5104-2-1 (Valve Rod) through the resin side of the gun.Use the 9301-5-1 (Seal Installation

SUPER PRO GUN &SUPER PRO GUN II20. Install the 5104-11-1 (Actuating Stem) into the 5104-2-1 (ValveRod).21. Actuate the 5104-11-1 (Valve Stem) back

SUPER PRO GUN &SUPER PRO GUN IIFig. 3.827. Position the 5104-12-1 (Mix Housing Seal) onto the backside ofthe 5104-20-1 (Mix Housing). See Fig. 3.

SUPER PRO GUN &SUPER PRO GUN IIChapter4SUPER PRO GUNSuperCutter Assembly 5101-01-01NOTEThe sharp edge of the Chopper Blades should be slightly dul

SUPER PRO GUN &SUPER PRO GUN II© 2001 Magnum Venus Products Manual Part No: M6707-1-1Corporate HQ & Mfg.Phone: (727) 573-2955Fax: (727) 571-36

SUPER PRO GUN &SUPER PRO GUN IIRotor Assembly1. Insert 9210-1-1 (Chopper Blades) between the 5103-28-1 (RotorHub) and 5103-29-1 (Wedge Insert). T

SUPER PRO GUN &SUPER PRO GUN IIFig. 4.4Fig. 4.3Rubber Roll Assembly5. Press the 5103-6-1 (Rubber Roll) onto the 5103-5-01 (MandrelAssembly). Secu

SUPER PRO GUN &SUPER PRO GUN II7. Slide Rubber Roll Assembly toward the 5103-03-01 (Wedge RotorAssembly) and tighten the 7102-2-20 (Socket Head Ca

SUPER PRO GUN &SUPER PRO GUN IINOTEProper adjustment has Idler Assembly touching the Rubber Roll, but still ableto rotate with minimum effort.Fig.

SUPER PRO GUN &SUPER PRO GUN II19Chapter5SUPER PRO GUNActuator Disassembly 5106-01-011. Unscrew the two 5105-13-1 (Rear Screws), and the two 5105-

SUPER PRO GUN &SUPER PRO GUN II20Chapter6SUPER PRO GUNHandle Disassembly 5105-00-011. Remove and discard the 5105-7-1 (Cylinder Gasket), and the51

SUPER PRO GUN &SUPER PRO GUN IINOTEDiscard all parts to be replaced by repair kit. All remaining parts should bethoroughly cleaned, inspected for

SUPER PRO GUN &SUPER PRO GUN IISUPER PRO GUNGun Block Disassembly 5104-00-0122Chapter71. Remove the four 5106-6-1 (Mounting Screws), and the four5

SUPER PRO GUN &SUPER PRO GUN II23NOTEDiscard all parts to be replaced by repair kit. All remaining parts should bethoroughly cleaned, inspected f

SUPER PRO GUN &SUPER PRO GUN IIChapter8SUPER PRO GUNSuperCutter Disassembly5103-00-011. Unscrew the 5103-14-1 (Cover Nut) and remove the 5103-13-1

SUPER PRO GUN &SUPER PRO GUN IITable of ContentsCHAPTER 1 - ASSEMBLY INSTRUCTIONSAssembly Instructions for Super Pro Gun II ActuatorAssembly Ins

SUPER PRO GUN &SUPER PRO GUN IIRotor Disassembly4. Loosen the two 7102-14-6 (Socket Cup Point Set Screws), andslide the 5103-03-01 (8-Blade Rotor

SUPER PRO GUN &SUPER PRO GUN IISUPER PRO GUN &SUPER PRO GUN IIAssembly DrawingsChapter926

SUPER PRO GUN &SUPER PRO GUN II27Fig. 9.1

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.228

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.329SUPER PRO GUN

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.430

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.531SUPER PRO GUN II

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.632

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.733

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.834

SUPER PRO GUN &SUPER PRO GUN IINOTETo order the correct repair kit, refer to the gun handle before ordering parts.SUPER PRO GUN Repair KitNOTEA Tu

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.935

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1036

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1137

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1238

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1339NOTEThese wedge rotors will not fit on the old style“classic” pro gun choppers (58605-1). They arefor Su

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1440

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1541

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1642

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1743

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1844

SUPER PRO GUN &SUPER PRO GUN IISUPER PRO GUN II Repair KitNOTEThe Super Pro Gun II is identified by either the blue handle or (on earlierversions

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.1945

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.2046

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.2147

SUPER PRO GUN &SUPER PRO GUN IIFig. 9.2248

SUPER PRO GUN &SUPER PRO GUN II

SUPER PRO GUN &SUPER PRO GUN II

SUPER PRO GUN &SUPER PRO GUN II© 2003 Magnum Venus Products Manual Part No: PRO-MGS-22Corporate HQ & Mfg.5148 113th Ave.Clearwater, FL 33760

SUPER PRO GUN &SUPER PRO GUN IISUPER PRO GUNActuator Assembly 5106-01-011. Install the 7301-3-020 (O-Ring) onto the 5106-7-1 (ActuatorPiston) and

SUPER PRO GUN &SUPER PRO GUN IINOTEThe Piston should be inserted “bushing end first”, with the bushing on the topside of center.5. Install the two

SUPER PRO GUN &SUPER PRO GUN IINOTEWhen installing the Trigger Assembly the 5105-8-1 (Trigger Lock) must be inthe “down” position.SUPER PRO GUNHan

SUPER PRO GUN &SUPER PRO GUN II4NOTEThe slot in the side of the 5105-5-1 (Porting Plate) must line up with the slotin the 5105-1-1 (Gun Handle).5.